Error 32 Induction plaque Bosch

What is the breakdown of Bosch error 32 affecting your induction hob?

If you have a Bosch induction hob, you may have encountered the error code 32 on the display at some point. This code indicates an issue with the electronic PCB board, which controls the operation of sensors, heating elements, and the fan.

But don't worry, today we have prepared a special article for you where we will reveal the possible causes and also the potential solutions you can apply to fix this issue. The error code 32 on your Bosch induction hob can occur for various reasons, such as:

• A fluctuation in the power supply causing a surge or drop in voltage.
• Defective or damaged wiring, both inside and outside the hob, preventing the proper flow of current.
• An accumulation of dirt or grease on the sensors or fan, hindering heat detection and proper cooling.
• Overheating of the hob due to prolonged or improper use, affecting electronic components.
• An internal failure of the electronic PCB board, requiring maintenance or possible replacement.

How to solve error 32 on the Bosch induction hob?

The good news is that this problem may have a solution, and we are going to leave you here a complete list of possible solutions that you can apply to fix error code 32 on induction hobs. the Bosch brand:

1. Restart your Bosch induction hob completely: When the error code 32 appears, the first step is to turn off the hob and disconnect it from the power supply. Then, wait for a few minutes and reconnect it before turning it back on. This may serve to restart the hob and refresh the sensors. If the code disappears, you can continue using the hob as usual. If not, you'll need to try other solutions.
2. Check that the power supply is stable and free from outages or voltage fluctuations: If necessary, use a regulator or a surge protector to prevent damage to the induction hob. Ideally, verify that the electrical supply is correct. Refer to the manufacturer's manual and ensure the electrical supply is suitable for your hob model. Also, remember that power outlets have limitations regarding amperage, so connecting multiple devices to the same outlet is not recommended.
3. Inspect the hob wiring, both internal and external: Disassemble your induction hob, uncover it, and make sure there are no loose, broken, cut, burnt, or scorched wires. If you detect any issues, replace the cable and then use a multimeter to check its proper continuity. Take the opportunity to inspect the connections and terminals of these cables; if you notice any defects, make the necessary repairs.
4. Clean the sensors and fan of the hob with a soft, dry cloth, avoiding abrasive products or water: Perform preventive maintenance on your Bosch induction hob, uncover it completely, and remove any dirt or grease that may interfere with its proper operation. Use an electronic cleaner to assist with this task, and if you have a multimeter, take the opportunity to check the continuity and integrity of the components of your induction hob.
5. Avoid using the hob for an extended period or at very high power, as this can lead to overheating: Follow the manufacturer's instructions regarding the maximum time and temperature of use. Additionally, use suitable induction-compatible cookware, and do not place them on the sensors or the fan of the hob.
6. If the problem persists, try repeating all the previous steps: You may need to perform a second check of everything described above to ensure you have followed everything accurately and find a solution to this problem.
7. Contact Bosch technical support to resolve the issue: If, after trying all these solutions, the error code E32 continues to appear, there may be a serious internal fault in the electronic PCB board. In that case, you will need to request a review of your induction hob from Bosch technical support. They can diagnose the problem and offer a repair or part replacement if necessary.

The error code 32 on Bosch induction hobs or ceramic cooktops indicates a problem with the electronic PCB board. The possible causes of this issue are as follows:

• Fluctuation in the power supply
• Defective or damaged wiring
• Accumulation of dirt or grease on the sensors or fan
• Overheating of the hob
• Internal failure of the electronic PCB board

Here are the steps you can try to resolve error code 32 on your Bosch induction hob:

• Restart your Bosch induction hob completely
• Check that the power supply is stable and free from outages or voltage fluctuations
• Inspect the hob wiring, both internal and external
• Clean the sensors and fan of the hob with a soft, dry cloth, avoiding abrasive products or water
• Avoid using the hob for an extended period or at very high power, as this can lead to overheating
• If the problem persists, try repeating all the previous steps
• Contact Bosch technical support to resolve the issue

And that's it! We are confident that with this article, you have understood the causes that can lead to this type of problem. We hope we have been helpful in finding a solution to error code 32 affecting your Bosch induction hob. Always remember to follow the manufacturer's instructions and consult with a Bosch professional if you have any doubts or difficulties.