Candy Dishwasher Error E3

What is the fault of error E3 Candy affecting your dishwasher?

We know that Candy dishwashers are synonymous with quality and energy efficiency, but have you encountered the E3 error code on your Candy dishwasher? If so, there's no need to worry because today, in this article, we will explain what this error means and how you can quickly and easily resolve it.

The E3 error code indicates that the water has not heated sufficiently during the washing cycle. This can be due to various reasons, such as a thermostat, heating element, or temperature sensor failure. These components are responsible for regulating and controlling the water temperature inside the dishwasher.

If the water doesn't reach the proper temperature, the dishwasher cannot perform the washing correctly, triggering the E3 error code on your appliance. This can affect the performance and efficiency of your appliance, as well as the cleanliness and hygiene of your dishes.

Please note that the E3 error code is synonymous with the 3 error code, so the possible causes and solutions are the same for both error codes on your Candy dishwasher.

How to fix E3 error in Candy dishwasher?

Here is a list of possible solutions you can apply to fix the E3 error code on Candy dishwashers:

1. Restart your dishwasher to refresh the sensors: Sometimes, a simple restart can resolve the error affecting your appliance. Disconnect the dishwasher from the power for a few minutes and then reconnect it. Start a washing cycle and check if the E3 error code persists on your dishwasher.
2. Check the status of the thermostat in your Candy dishwasher: The thermostat regulates the water temperature according to the selected program. If it's damaged or misaligned, it may prevent the water from heating sufficiently. To check it, you'll need a multimeter and electronics knowledge. If the thermostat is damaged, you'll need to replace it with a new one compatible with your Candy dishwasher model.
3. Inspect the heating element of your Candy dishwasher: The heating element is responsible for heating the water inside the dishwasher. If it's broken or dirty, it may prevent the water from reaching the desired temperature. To verify it, you'll also need a multimeter and follow the user manual instructions. If the heating element is damaged or dirty, you'll need to replace or clean it as necessary.
4. Check the temperature sensor of your Candy dishwasher: The temperature sensor measures the water temperature and sends the information to the thermostat, which then signals the dishwasher's PCB electronic board. If this sensor is misplaced or damaged, it can send incorrect signals and trigger the E3 error code on your appliance. To check it, locate it inside the dishwasher and verify its condition and position. If it's defective or displaced, adjust or replace it as necessary and compatible with your Candy dishwasher model.
5. If the problem persists, please repeat all the previous steps and ensure you follow everything precisely: You may have overlooked some detail or need to perform additional tests to identify the cause of the error. Please review all the steps mentioned earlier and recheck everything if necessary. If the problem persists, it's best to leave the matter to the experts.
6. Arrange a home visit from Candy's technical support for a thorough inspection of your dishwasher: If, after performing all the above checks, you haven't been able to fix the E3 error code, it's likely a more complex issue that requires the intervention of a qualified professional. Contact Candy's official technical service and request a home visit for a technician to review your dishwasher and provide the best possible solution.

In summary, the E3 error code means that the water has not heated enough during the washing cycle. This could be due to a thermostat, heating element, or temperature sensor failure. To address it, you can try the following:

• Restart your dishwasher to refresh the sensors
• Check the status of the thermostat in your Candy dishwasher
• Inspect the heating element of your Candy dishwasher
• Check the temperature sensor of your Candy dishwasher
• If the problem persists, please repeat all the previous steps and ensure you follow everything precisely
• Arrange a home visit from Candy's technical support for a thorough inspection of your dishwasher

We hope this article has been helpful, and you've been able to fix the E3 error code on your Candy dishwasher. Remember that if you can't find a solution to this problem, you can always rely on Candy's technical support. Good luck and happy washing!