Corberó Ceramic glass Error 99

What is the failure of error 99 Corberó that is affecting your ceramic hob?

Have you encountered error code 99 on your Corberó ceramic hob? And unfortunately, you don't know what it means or how to fix it. Well, don't worry! Because in this article, we'll explain everything you need to know about this annoying issue that can affect the operation of your appliance.

Error code 99 is a fault that indicates a problem with the electronic PCB board of the ceramic hob, which is responsible for controlling and regulating the operation of sensors, controls, and resistors. This problem is usually due to a strong surge in the electrical supply, which can damage or burn out a component of the board.

If you have encountered this error, the first thing you should do is identify the possible causes that have triggered it. Below, we provide a list of the most common ones:

• A sudden power outage or drop, which can alter the voltage and cause a surge.
• A faulty or damaged power outlet or cable, which can cause a short circuit or poor connection.
• An overload in the electrical circuit, due to too many devices connected at the same time or exceeding the amperage of the electrical connection.
• An old or poorly done electrical installation, which may have faults or irregularities in the supply.
• An electrical storm, which can generate atmospheric discharges that affect the power supply.

All of these causes can lead to error code 99 appearing on your Corberó ceramic hob. Unfortunately, problems affecting PCB electronic boards are very difficult to repair unless you have advanced knowledge in electronics. However, we have prepared for you a list of possible solutions that you can apply before considering your ceramic hob completely lost.

How to fix error 99 on the Corberó ceramic hob?

Once you have identified the cause of the error, you can proceed to apply the possible solutions. We recommend that you follow these steps in order, until error code 99 disappears from your Corberó ceramic hob:

1. Turn off and unplug the ceramic hob from the power supply to reset and refresh its sensors: This could be the simplest step of all and is the one we recommend you do first. Completely turn off your ceramic hob and unplug it from the power outlet for a few minutes. Then, reconnect it and check if error code 99 has disappeared.
2. Check the power outlet and power cable of the ceramic hob: Make sure they are not damaged, corroded, loose, or burnt. If necessary, perform maintenance on them, tighten them securely, or replace them with new ones suitable for your ceramic hob model.
3. Inspect the fuse and wiring in the general electrical panel of your home: Check the electrical wiring in your home that communicates with the kitchen area or where the ceramic hob is installed. Make sure that this wiring and the fuses are in excellent working condition and are not corroded, cut, burnt, or scorched.
4. Reduce the number of electrical devices connected to the same circuit as the ceramic hob: You may not know this, but you cannot connect many devices to the same power outlet. This is because the amperage of each power outlet is limited, and connecting many devices can cause instability in the electrical supply to your home. Try connecting the ceramic hob to another power outlet and this time connect it alone on this circuit and check if error code 99 has disappeared.
5. Verify the power that the ceramic hob needs to work and the power you are supplying: Some ceramic hobs operate with a base voltage of about 220v. Please make sure you have the necessary voltage at the power outlet where you have the ceramic hob connected. If the appliance does not receive the correct electrical voltage, it may not function properly and may be damaged over time. Consult the manufacturer's manual for your ceramic hob model to ensure you are using the correct electrical supply.
6. Electronically check the electronic PCB board of your Corberó ceramic hob: Use a multimeter and check each of the components connected to the electronic PCB board. Make sure this board does not have any sulfate, burns, or bulging or exploded components. If you detect any type of fault or if the board does not have continuity in any of its components, then you will have to replace it with a new one that is compatible with your ceramic hob model.
7. If the problem persists, please repeat all the previous steps and make sure to follow everything to the letter: You may have overlooked some detail or not performed a check correctly. That is why we recommend you to make a second check of everything we have mentioned above and to pay more attention to detail. If the problem still persists, then it may be time to leave this problem in the hands of the experts.
8. Call a Corberó technical service and request a home visit for a more thorough inspection: The error may be due to internal damage to the electronic PCB board and may require extensive repair or a complete replacement. For this, you will have to call the Corberó technical service to give you a hand with this problem. We are sure that you are in very good hands, do not be afraid and proceed with the repair of your ceramic hob.

In summary, error code 99 in Corberó ceramic hobs is a fault that indicates a problem with the electronic PCB board, caused by a voltage surge in the electrical supply. To fix it, you must identify the cause of the problem and apply the appropriate solutions:

• Turn off and unplug the ceramic hob from the power supply to reset and refresh its sensors
• Check the power outlet and power cable of the ceramic hob
• Inspect the fuse and wiring in the general electrical panel of your home
• Reduce the number of electrical devices connected to the same circuit as the ceramic hob
• Verify the power that the ceramic hob needs to work and the power you are supplying
• Electronically check the electronic PCB board of your Corberó ceramic hob
• If the problem persists, please repeat all the previous steps and make sure to follow everything to the letter
• Call a Corberó technical service and request a home visit for a more thorough inspection

We hope this article has been helpful to you and that you have been able to fix error code 99 on your Corberó ceramic hob. Good luck!