Beko Air Conditioning Error e1

What is the fault of the Beko E1 error affecting your air conditioner?

Oh no! The summer season has arrived, and your air conditioner is displaying an error code. It's time to understand what we're dealing with so you can enjoy the coolness this season and forget about the heat.

As we all know, air conditioning allows us to maintain a pleasant temperature in our home and/or workplace. The E1 error code on Beko brand air conditioners indicates that there is a problem with the temperature sensor, specifically the one located in the indoor unit.

In this article, we will explain what this error code means, its possible causes, and how to resolve it simply and effectively. This way, you can prevent major damage to your equipment and save time and money on repairs.

The temperature sensor in the indoor unit is responsible for measuring the air temperature entering and leaving the device. This information is sent to the controller to regulate the operation of the compressor and the fan. If this sensor fails or does not receive the correct signal, it can lead to this type of error where it displays the E1 error code both on the split unit and on the remote control of the device.

The E1 error code in Beko air conditioners can have several causes, including:

• The sensor is dirty or damaged: Dust, moisture, or a blow can affect the sensor and cause it to malfunction. This can alter the temperature reading and lead to the failure.
• Wiring is loose or cut: The sensor is connected to the controller by cables that can come loose or be cut for some reason. This prevents communication between both components and generates this type of error in your air conditioner.
• The controller is defective: The controller is the brain of the air conditioner and is responsible for processing the information received from the sensor and sending commands to the compressor and the fan. If the controller is damaged, it may misinterpret the sensor signal or not send the correct commands.

How to fix the Beko air conditioner E1 error?

The good news amidst all this trouble is that you don't have to endure the heat during this summer season, and you can reactivate your air conditioner by following our advice. To resolve the E1 error code, you can follow these steps outlined below:

1. Restart the air conditioner: Sometimes, a simple restart can resolve the problem because it resets the sensors. To do this, turn off your air conditioner completely using the remote control, disconnect it from the power outlet, and wait for a few minutes. Reconnect and turn it back on to check if the error has disappeared. If the error is persistent, then you'll need to proceed with the following steps.
2. Clean the temperature sensor: Perform preventive maintenance on your air conditioner to clean this temperature sensor. If the sensor is dirty, you can clean it using an electronic cleaner and a soft-bristle brush. Be careful not to damage it with any sharp objects or excessive force. After cleaning, turn the air conditioner back on and verify if the error has disappeared.
3. Inspect the temperature sensor wiring and/or the PCB board: If the wiring is loose, cut, burned, or scorched, you can try to reconnect it properly or replace it with a new one. To do this, you'll need to open the housing of the indoor unit with a screwdriver and locate the cables running from the sensor to the control board. Make sure to disconnect the equipment from the power source before handling the cables. Once you have fixed the wiring, turn on the air conditioner and check if the error code has disappeared.
4. Replace the temperature sensor: Check your sensor with a multimeter to see if it has continuity or not. You'll need electronics knowledge to do this yourself, and if the sensor is damaged, you'll have to replace it with a new one. After changing the sensor, turn on the air conditioner and check if the error has disappeared.
5. Replace the controller or the PCB board: Check if the components on the PCB board have good continuity with a multimeter; otherwise, you'll need to locate the replacement and replace it entirely. After changing the controller or the PCB board, turn on the air conditioner and verify if the error has been resolved or not.
6. Review all the steps we've described earlier: If after completing all the previous steps, the error continues to appear on your Beko air conditioner, there may be some other damaged component, or the problem may be more complex than it seems. In that case, we recommend that you go through all the previous steps again with more care and attention to ensure that you haven't missed any details.
7. You can contact Beko's technical support to resolve this issue: If after repeating all the previous steps, the error still persists, you most likely need the assistance of a qualified professional. And who better than Beko's technical service? The same manufacturer provides a service where you can seek help in such cases. You have nothing to lose by giving them a call and requesting their service, especially if the equipment is still under warranty.

In summary, the E1 error code in Beko air conditioners is a problem related to a temperature sensor. Here is a summary of the steps we have detailed earlier to help you find a solution to this issue:

• Restart the air conditioner
• Clean the temperature sensor
• Inspect the temperature sensor wiring and/or the PCB board
• Replace the temperature sensor
• Replace the controller or the PCB board
• Review all the steps we've described earlier
• Contact Beko's technical support to resolve this issue