Beko Air Conditioning Error p4

What is the fault of the P4 Beko error affecting your air conditioner?

Summer has arrived, you're about to turn on your air conditioner, and bam! An error code pops up, preventing you from enjoying cool air and forcing you to endure the heat. Don't worry, in this article, we'll explain what this error means, what its possible causes are, and how you can quickly and easily resolve it.

The P4 error code indicates that the air conditioner's compressor is not turning on. The compressor is responsible for compressing the refrigerant gas and circulating cool air throughout the cooling system. If the compressor isn't functioning, the air conditioner won't be able to cool the environment.

However, the fact that the compressor isn't turning on doesn't necessarily mean it's damaged. There could be other reasons why the air conditioner displays the P4 error code, and we'll provide you with a list of possible causes that could lead to this issue:

• A problem with the electrical wiring: There may be a loose, cut, burned, or scorched wire that prevents the compressor from receiving the proper electrical current.
• A problem with the power supply: There may be a power outage, voltage drop, or a failure in the plug or switch that supplies power to the air conditioner.
• A problem with the thermostat: There may be an incorrect setting, improper calibration, or a malfunction in the thermostat that prevents the correct signal from being sent to the compressor to turn it on.
• A problem with the PCB electronic board: There may be a short circuit, overload, or a malfunction in the electronic board that controls the operation and/or starting of the compressor.

How to solve the P4 error of the Beko air conditioner?

Fortunately for our Beko air conditioners, this type of issue can have a solution. Below, we provide a list of possible solutions you can try to resolve this problem on your own:

1. Restart the air conditioner: The first thing you should do is turn off the air conditioner, disconnect it from the electrical outlet, and wait for a few minutes. Then, reconnect it and turn it on to see if the error has disappeared. This procedure can help recalibrate and/or reset the air conditioner's sensors.
2. Check the electrical wiring of the air conditioner: You should verify that all cables are properly connected, without damage or signs of burning or scorching due to overheating. If you find any defective cables, you should replace or repair them.
3. Check the power supply of the air conditioner: You should ensure that the electrical voltage is appropriate for your air conditioner. Remember that most air conditioners operate at a voltage of 220v. If, for any reason, the voltage is not reaching the full level, the compressor will not start, and the air conditioner will display this P4 error code. Also, check that the air conditioner's plug and switch are functioning correctly, as well as the voltage regulator you have installed. If there is any issue with the power supply, you should resolve it or change the power outlet.
4. Check the thermostat of the air conditioner: You should verify that the thermostat is properly configured, calibrated, and clean. Try performing preventive maintenance on it using an electronic cleaner and a soft-bristle brush. If there is any issue with the thermostat, you should adjust, replace, or repair it.
5. Check the PCB electronic board of the air conditioner: Ensure that the electronic board has no visible damage or signs of overheating. Use a multimeter to check the continuity of the components on the PCB board. If there is any issue with the electronic board, you should replace or repair it with the assistance of a professional.
6. Repeat all the previous steps if the problem persists: If, after performing all the previous checks and solutions, the air conditioner continues to display the P4 error code, you should repeat the entire process from the beginning to ensure that nothing has been overlooked. Make sure to follow all the steps to the letter and leave nothing to chance.
7. Contact Beko's technical support: If, after repeating all the previous steps, the air conditioner still does not work correctly, you should get in touch with Beko's official technical service. Schedule an appointment with them to send a specialized technician to inspect and repair your air conditioner as soon as possible.
8. Replace the air conditioner compressor: As a last resort, you can consider replacing the air conditioner compressor. However, we recommend that you have this diagnosis performed by a specialized or qualified technician. There's nothing better than an expert in the field to advise you after conducting all the previous inspections, as a new compressor for your air conditioner could be a fairly costly component.

To conclude our list of tips, we can inform you that the P4 error code in Beko air conditioners is related to a fault in the compressor or the voltage supply it receives. To resolve it, you can do the following:

• Restart the air conditioner
• Check the electrical wiring of the air conditioner
• Check the power supply of the air conditioner
• Check the thermostat of the air conditioner
• Check the PCB electronic board of the air conditioner
• Repeat all the previous steps if the problem persists
• Contact Beko's technical support
• Replace the air conditioner compressor

We hope this article has been helpful, and that you have been able to resolve the P4 error code on your Beko air conditioner. Be sure to carefully review all the steps as we have detailed them before making the decision to replace the air conditioner compressor. Goodbye!