Error E14 Dishwasher Bosch

What is the fault of the E14 Bosch error affecting your dishwasher?

Do you have a Bosch dishwasher and the Error Code E14 has appeared on the screen? Don't worry, in this article, we'll explain what this error means, as well as its possible causes and how you can easily and quickly fix it.

The E14 error code on Bosch dishwashers indicates that there's a problem with the flow of water entering the dishwasher. This can be due to various reasons, such as an obstruction in the water inlet, a bent or damaged hose, a faulty water flow sensor, or insufficient water flow.

If this problem is not resolved, the dishwasher will not be able to fill with water properly and won't be able to complete the washing cycle. Among the possible causes of this issue, we have the following:

• Water inlet blocked or clogged: There may be an object or dirt blocking the passage of water into the dishwasher.
• Water inlet hose bent or damaged: The hose connecting the shut-off valve to the dishwasher may be bent or have a crack that hinders the correct and adequate flow of water.
• Water flow sensor damaged: The water flow sensor measures the amount of water entering the dishwasher and sends the signal to the control panel or electronic PCB. If this sensor fails, the dishwasher may detect an error in the water flow and display the E14 code.
• Water flow or pressure insufficient: It could be that the water pressure is too low, and an insufficient amount of water reaches the dishwasher. This could be due to a malfunction in the supply network or a poorly regulated shut-off valve.

How to fix the E14 error of the Bosch dishwasher?

Fortunately, this problem has a quick and effective solution. Below we will leave you a series of steps to follow so that you can find a solution to the E14 error code in your Bosch dishwasher:

1. Restart the dishwasher to reset the sensors: Sometimes, a simple restart can solve the problem and make the sensors function correctly again. To do this, disconnect the dishwasher from the power for a few minutes and reconnect it. Then, start a washing cycle and check if the E14 error has disappeared.
2. Clean the water inlet and filter of the dishwasher: If you have detected any obstruction in the water inlet or filter, clean them with warm water and a soft brush or a damp cloth to remove any residue that may block the water passage. Then, reconnect the hose and open the shut-off valve. Start a washing cycle and observe if the E14 error has been resolved.
3. Replace the water inlet hose of the dishwasher: If you have confirmed that the hose is bent or damaged, replace it with a new one of the same type and size. Ensure that it is securely attached to both the shut-off valve and the dishwasher. Then, open the shut-off valve and start a washing cycle. Verify if the E14 error has been resolved.
4. Ensure that the water pressure is correct: Open the shut-off valve completely and check that the water flow is sufficient to supply your dishwasher. Remember that your appliance simply won't function without water.
5. Replace the water flow sensor of the dishwasher: Use a multimeter for assistance. If you have measured the resistance of the sensor and confirmed that it is damaged, you'll need to replace it with a new one of the same model. To do this, disconnect the cables connecting it to the control panel and carefully remove it. Then, place the new sensor in its position and connect the cables. Start a washing cycle and check if the E14 error has been resolved.
6. Repeat all the previous steps if the problem persists: If you have followed all the above solutions and the E14 error continues to appear, there may be another damaged component or the problem may be more complex than it seems. In that case, we recommend that you repeat all the previous steps with more attention and care, ensuring that everything is in order.
7. Seek assistance from Bosch technical support to solve the problem: If, after repeating all the previous steps, the E14 error has not been resolved, you likely need the help of a qualified professional. Without a doubt, the best in this matter are the technicians from Bosch's official technical support. You can contact Bosch and request a home visit. They will diagnose and repair the problem with the utmost speed and efficiency.

In summary, the E14 error code indicates that there is a problem with the flow of water entering the Bosch dishwasher. Possible causes include a blocked water inlet, a bent or damaged water inlet hose, a faulty water flow sensor, or insufficient water flow or pressure. The possible solutions to address this E14 error code in your dishwasher would be as follows:

• Restart the dishwasher to reset the sensors
• Clean the water inlet and the dishwasher filter
• Replace the dishwasher's water inlet hose
• Ensure that the water pressure is correct
• Replace the dishwasher's water flow sensor
• Repeat all the previous steps if the problem persists
• Seek assistance from Bosch technical support to resolve the problem

And basically, that would be it! We truly hope we've been able to help you resolve the E14 error code in your Bosch dishwasher. Remember that for extending the lifespan of your dishwasher, regular preventive maintenance is always necessary. Good luck and until next time!