Error E63 Dryer Bosch

What is the fault of Bosch error E63 affecting your dryer?

If you're here, it's because you're having issues with your Bosch dryer, and the E63 error code has appeared. If that's the case, let me assure you there's no need to worry. In this article, we'll explain what this error could mean, its possible causes, and how we're going to solve it in the best possible way.

Unfortunately, the E63 error code is a fault indicating that there is a problem with the dryer's electronic PCB (Printed Circuit Board), making it a serious issue. This board is responsible for controlling sensors, programs, cycles, and the general operation of the appliance. When damaged or misconfigured, it can cause the dryer to malfunction or stop in the middle of a cycle.

These are the possible causes that can lead to the appearance of the E63 error code on your Bosch dryer's display:

• A power outage or voltage surge that has affected the electronic PCB.
• A poor connection or a loose cable on the board or one of the sensors.
• An accumulation of lint or dirt that has obstructed a sensor or fan.
• An overheating of the appliance due to insufficient ventilation or an excessive load of clothes.
• A factory defect or wear and tear from prolonged use of the electronic PCB.

All of these causes can lead to this type of error on your dryer, so we'll need to conduct a somewhat thorough inspection to find the definitive solution to this problem.

How to fix Bosch dryer error E63?

There are solutions that you can try to fix this fault that your dryer has, some of them you can try yourself without having to call technical support. To find a solution to error code E63 in Bosch dryers, you can follow these steps below:

1. Restart the dryer to reset the sensors: Let's start with the simplest solution by restarting your dryer to give a break and rest to all its sensors. To do this, disconnect the dryer from the power outlet for a few minutes and then reconnect it. Now turn it on and check if the error code has disappeared. Sometimes, such faults can be resolved this way, as the sensors return to their default values. If the problem persists, then continue reading to see if we can find a solution to this issue.
2. Check the connections and cables of the electronic PCB and sensors: Ensure that there are no loose, broken, torn, cut, burned, or scorched cables. This wiring must be in excellent condition without any exceptions. If you find any issues, repair or replace the necessary cables.
3. Clean the dryer and remove lint or dirt from the interior: Pay special attention to the filter, condenser, drum, and fans. Use a damp cloth and a vacuum cleaner to remove lint residues or any dirt that may interfere with the normal operation of the dryer. Avoid using abrasive or flammable products that could damage the parts.
4. Adjust the temperature and load of the dryer: Avoid using very hot programs or cycles and do not overload the drum with clothes. Leave enough space for air circulation and proper drying of the clothes. This will prevent the appliance from overheating and damaging the electronic PCB or any other component of your dryer.
5. Repeat all the previous steps if the problem persists: Make sure to follow all the steps we've outlined above. Perform a second check of everything we've described. If after performing all these actions the E63 error code continues to appear, the electronic PCB may be faulty and may need to be replaced.
6. Check the electronic PCB of your dryer: For this step, you will need advanced knowledge of electronics. Use a multimeter and locate the electronic PCB of your dryer, usually located at the top and behind the control panel. Check for continuity in all its components, ensuring it is not sulfated or showing signs of electrical flashes or burning. If possible, perform maintenance with electronic cleaner or a small ultrasonic bath. If the problem persists and you cannot find a solution, it's time to leave the matter to the experts.
7. Call Bosch technical support to solve the problem: If you cannot repair the error on your own or if you have doubts about how to do it, it's best to contact a qualified professional to inspect your dryer and provide an appropriate solution. Who better than Bosch's technical support to help you resolve this issue? We are confident that you are in good hands. Give Bosch a call and schedule a home visit from one of their technicians.

In summary, the E63 error code in Bosch dryers indicates a problem with the electronic PCB of the Bosch dryer. Possible causes include a power outage or surge, poor connection or loose cable, accumulation of lint or dirt, overheating of the appliance, or a factory defect or wear and tear from usage. Possible solutions for you to fix this problem on your own are as follows:

• Restart the dryer to reset the sensors
• Check the connections and cables of the electronic PCB and sensors
• Clean the dryer and remove lint or dirt from the interior
• Adjust the temperature and load of the dryer
• Repeat all the previous steps if the problem persists
• Check the electronic PCB of your dryer
• Call Bosch technical support to solve the problem

We hope this article has been helpful, and you have been able to resolve the E63 error code on your Bosch dryer. Remember to always keep your dryer with a stable flow of electrical supply to avoid such inconvenient situations, as well as good preventive maintenance to ensure its proper operation and extend its lifespan. Thank you very much for reading!