Error 29 Washer Bosch

What is the fault of error 29 Bosch that is affecting your washing machine?

Have you ever experienced that when you start your Bosch washing machine, an error message appears on the screen? And that message is the error code 29? If so, don't worry, because in this article, we will explain what this error could mean and how we might solve it.

Error code 29 is one of the most common errors that can appear on Bosch washing machines. It indicates that there is an issue with the water pressure or flow reaching the washing machine, meaning that it's either not receiving enough water or very little water. This can affect the normal operation of the washing machine and lead to issues during washing, spinning, and/or draining. Keep in mind that this type of issue can also affect Bosch Series 6 washing machines, and error 29 is synonymous with error E29, so the causes and solutions to resolve the problem are the same.

Fortunately, this type of issue is easily fixable. But to solve it, first, we need to examine the possible causes that could trigger error code 29:

• The water tap is closed or has low pressure: This can happen due to a water installation issue or a temporary water supply interruption.
• The water inlet filter is dirty or clogged: The filter is a component located in the hose that connects the tap to the washing machine, designed to prevent impurities from entering the appliance. Over time, the filter can accumulate dirt and reduce water flow.
• The water inlet hose is bent, twisted, or blocked: This can prevent water from flowing properly into the washing machine, causing a decrease in pressure or flow.
• The water level sensor is faulty: The sensor is an electronic component that measures the amount of water in the washing machine drum and sends a signal to the mainboard to regulate the washing cycle. If the sensor fails, it can send an incorrect signal, leading the washing machine to detect a water problem.

How to fix error 29 on the Bosch washing machine?

In order to resolve error code 29 on Bosch washing machines, you can follow the following tips and advice provided below. Remember that if you get stuck at any of these steps, it's best to call an expert to assist you with the issue:

1. Reset the washing machine to reset the sensors: Sometimes, error code 29 can be a false positive caused by a temporary system glitch. In that case, simply turn off the washing machine, disconnect it from the power source, wait for a few minutes, and then reconnect it to turn it on again. This will clear the appliance's memory and reset the sensors.
2. Check the water tap and open it fully if necessary: If the tap is closed or has low pressure, it's important to open it fully to ensure a proper water supply to the washing machine. You can also verify that you have water supply in the part of the house where your washing machine is connected. Check if you happen to have a shut-off valve closed, and if so, open it fully and confirm if your washing machine is now receiving water normally.
3. Clean the water inlet filter: If the filter is dirty or clogged, it needs to be cleaned to remove any dirt residues that may be blocking the water flow. To do this, you should disconnect the washing machine from the tap and the power outlet, remove the water inlet hose, unscrew the filter using a wrench or pliers, take it out, and clean it with a soft-bristle brush and warm water. Then, reposition it and reconnect the hose to the tap and the washing machine.
4. Check the water inlet hose: This hose should not be bent, excessively twisted, or crushed against a wall or the washing machine itself. If the hose is improperly positioned, it needs to be properly adjusted and straightened to facilitate the water flow to the washing machine. Also, ensure that there are no objects pressing against or damaging the hose, such as furniture or other appliances.
5. Inspect the water level sensor: If the sensor is damaged, it should be replaced with a new one to ensure proper functionality. Try performing preventive maintenance first before replacing it; use an electronic cleaner and a multimeter to check for continuity. Remember that sometimes sensors can go haywire when you use too much detergent to wash clothes.
6. Repeat all the previous steps if the problem persists: If error code 29 continues to appear on the screen after trying all the previous solutions, you should go back and repeat the steps from the beginning to ensure that no detail has been overlooked or that there is no other hidden issue.
7. Contact Bosch technical support to resolve the issue: If none of the previous solutions work, it's likely that there is a serious malfunction in the washing machine preventing it from operating normally. In such cases, you should get in touch with Bosch's customer support and request a visit from an official technician to inspect your washing machine. Schedule an appointment with them, and we are confident they will find a solution for your washing machine.

In summary, to conclude this guide of tips that we have prepared for you, error code 29 on Bosch washing machines indicates that there is a problem with the water pressure or flow reaching the washing machine. To resolve this issue with your appliance, in brief, we could tell you to do the following:

• Reset the washing machine to reset the sensors.
• Ensure that the water tap is open; if not, open it fully.
• Clean the water inlet filter.
• Inspect if the water inlet hose is bent or crushed.
• Check the water level sensor because excess foam can sometimes be your worst enemy.
• Repeat all the previous steps if the problem persists.
• Contact Bosch technical support to resolve the issue.