Error 18 Washer Bosch

What is the error 18 Bosch fault affecting your washing machine?

Hello! In this article, we're going to talk to you about the error code 18 on Bosch washing machines. You've probably encountered this issue at some point and don't know what to do. Don't worry because we're going to explain everything you need to know about this error, its causes, and its solutions. Keep reading, and you'll see it's not as serious as it seems!

Please note that error code 18 on Bosch washing machines also applies to the Avantixx 7, Avantixx 8 models, and, of course, the Series 6 is also included in this list. Another detail to consider is that error code 18 is synonymous with error code E18, so they are the same error, and the causes and solutions are the same for each of them.

Error code 18 on Bosch washing machines indicates that the appliance has problems draining water. This issue can have several causes, so we'll mention some of them:

• The pump filter is obstructed by a foreign object: Coins, buttons, lint, etc., are enemies of your washing machine's filter and the drainage pump itself.
• A damaged drain hose: If this hose is bent, crushed, or blocked by any residue, it can cause this error code to appear.
• The drainage pump is faulty or defective: It may not necessarily be damaged, but it may need proper maintenance because it could be clogged.
• A water level sensor that is dirty or damaged: Keep in mind that excessive foam can cause sensors to throw errors like false positives. So you'll likely need to perform preventive maintenance on this sensor.

These are some of the possible causes that can trigger this issue, but there may be others. The important thing is that you know how to resolve this problem and prevent it from happening again in the future.

How to fix the error 18 on the Bosch washing machine?

Fortunately, error code 18 or E18 has a quick and easy solution. It is a completely repairable error, and to resolve this issue without the need to call technical support and spend extra money, you just need to follow the steps below:

1. Restart the washing machine to reset the sensors: Occasionally, excessive foam or an overload in electrical voltage can trigger false positive errors because the sensors become uncalibrated. To do this, you'll need to completely turn off your washing machine and unplug it from the power outlet for a few minutes. Now, plug it back in, turn it on, and check if this error code has disappeared.
2. Clean the pump filter: To do this, you have to open the cover located at the front bottom of the washing machine, remove the filter by turning it counterclockwise, and remove any objects that may be obstructing it. Once it's clean, put it back in place and close the cover.
3. Check the washing machine's drain hose: Ensure that this hose is not bent, crushed, or blocked by any residue or foreign objects. If necessary, disconnect the hose completely and clean the inside with a soft wire. You can also blow through the hose to remove any obstructions. Reconnect it once it's clean and position it naturally, without it being too bent or tightly pressed against the wall or the washing machine.
4. Inspect the drainage pump: Remove it from the washing machine and thoroughly inspect it. Look for foreign objects that may be obstructing it. If the pump is damaged, you will need to replace it with a new one.
5. Clean the water level sensor: This sensor is located at the top of the washing machine, near the drum. To clean it, you need to remove the top panel of the washing machine, locate the sensor (usually a round piece with two wires), and clean it with an electronic cleaner or alcohol. Wait for it to dry and reconnect it. Sometimes, excessive foam or an electrical voltage overload can cause this sensor to malfunction and not work properly.
6. Repeat all the previous steps if the problem persists: Please follow all the steps precisely. If you are sure you have done everything correctly, you can perform a second check and proceed. If the error persists even after double-checking, then it may be time to leave the problem in the hands of the experts.
7. Seek Bosch technical support to resolve the issue: If none of the above works, it's best to contact Bosch's official technical service to help you resolve the problem. They have the necessary means and knowledge to repair your washing machine and ensure its proper functioning. Schedule an appointment with a qualified professional!

In summary, error code E18 in Bosch washing machines indicates that there is a problem with water drainage in your washing machine. To address this issue and find a solution, you would need to perform these steps summarized as follows:

• Restart the washing machine to reset the sensors
• Clean the pump filter
• Check the drain hose
• Inspect the drainage pump
• Clean the water level sensor
• Repeat all the previous steps if the problem persists
• Seek Bosch technical support to resolve the issue

I hope this article has been helpful, and you have been able to resolve error code 18 on your Bosch washing machine. Remember to keep your washing machine properly maintained to extend its lifespan and enjoy it to the fullest. Goodbye and happy washing!