Corberó Induction plaque Error 99

What is the fault of error 99 Corberó that is affecting your induction hob?

Hello! If you're here, it's because you've encountered the error code 99 on your Corberó induction hob. You probably don't know what to do or how to fix it, but don't worry too much because today we're going to explain everything you need to know about this annoying issue that can greatly affect the functioning of your appliance.

The error code 99 on Corberó induction hobs is a fault that indicates a problem with the PCB electronic board. This board is responsible for controlling and regulating the operation of sensors, controls, and resistors. This problem is usually due to a strong surge in the electrical supply, and unfortunately, it's a problem that can be very difficult to fix unless you completely replace the electronic board.

If you've encountered this error code on your induction hob, the first thing you should do is identify the possible causes that may have caused it. Below, we'll list the most common causes of this fault:

• A sudden power outage or drop, which can alter the voltage and cause a voltage spike.
• A defective or faulty power outlet and/or cable, which can cause a short circuit or poor connection.
• An overload in the power circuit of the power outlet, due to too many devices connected at the same time or exceeding the amperage of the electrical connection.
• A very old electrical installation or one that may be poorly done, which may have faults or irregularities in the supply.
• An electrical storm, which can generate atmospheric discharges that affect the power supply from the electrical grid.

All these causes can lead to the error code 99 appearing on your Corberó induction hob. Unfortunately, problems affecting PCB electronic boards are very difficult to repair unless you have advanced knowledge in electronics. But don't lose hope, let's see how we could solve this problem.

How to solve error 99 of the Corberó induction hob?

Here's a list of possible solutions you can apply to fix error code 99 on Corberó induction hobs on your own without needing to call a technician:

1. Turn off and unplug the induction hob from the power supply to reset and refresh its sensors: This procedure is the simplest of all and is recommended to be done first. To do this, completely turn off your induction hob and unplug it from the power outlet for a few minutes. Then, plug it back in and check if error code 99 has disappeared on your induction hob.
2. Check the power outlet and the power cable of the induction hob: Ensure that this power outlet is not damaged, sulfated, loose (poorly connected), or burnt. If necessary, perform a general maintenance, tighten it well, or replace it with a new and appropriate one according to the model of your induction hob.
3. Inspect the fuse and electrical wiring of your home: Check the electrical wiring in your home that connects to the kitchen area or where the induction hob is installed. Please ensure that this wiring and the fuses are in excellent working condition and are not sulfated, cut, poorly connected, or burnt.
4. Reduce the number of electrical appliances connected to the same power outlet as the induction hob: We assume you didn't know that many devices cannot be connected to the same power outlet. This is because the amperage of each power outlet is limited, and connecting many devices can cause instability in the electrical supply of your home. Try connecting your induction hob to another power outlet and this time connect it alone and check if error code 99 has disappeared.
5. Verify the power needed for your induction hob to operate and the power you are supplying it: Some induction hobs operate with a base voltage of about 220v. Please ensure you have the necessary voltage in the power outlet where your induction hob is connected. If the appliance does not receive the appropriate electrical voltage, it may not function correctly and may become damaged over time. Consult the manufacturer's manual according to the model of your induction hob and ensure you are using the appropriate electrical supply.
6. Check the PCB electronic board of your induction hob with a multimeter: Check each of the components connected to the PCB electronic board and verify whether they have stable continuity or not. Make sure this board does not have any sulfates, burns, or bulging or exploded components. If you detect any type of failure or if the board does not have continuity in any of its components, then you will have to replace it with a new one that is compatible with the model of your induction hob.
7. If the problem persists, please repeat all the previous steps and make sure to follow everything to the letter: You may have missed some detail or not performed a check correctly. That's why we recommend you to do a second check of everything we mentioned earlier and pay more attention to detail. If the problem still persists, then perhaps it's time to leave this problem in the hands of experts.
8. Call a Corberó technical service and request a home visit for a more thorough inspection: The error may be due to internal damage to the PCB electronic board and may require extensive repair or complete replacement. To do this, you will have to call Corberó technical service to lend you a hand with this problem. We are sure we are leaving you in very good hands, so do not be afraid and proceed with the repair of your induction hob.

In summary, the error code 99 on Corberó induction hobs is a fault that indicates a problem with the PCB electronic board. This fault may be caused by a surge in voltage in the electrical supply. To fix it, we recommend following these steps:

• Turn off and unplug the induction hob from the power supply to reset and refresh its sensors
• Check the power outlet and the power cable of the induction hob
• Inspect the fuse and electrical wiring of your home
• Reduce the number of electrical appliances connected to the same power outlet as the induction hob
• Verify the power needed for your induction hob to operate and the power you are supplying it
• Check the PCB electronic board of your induction hob with a multimeter
• If the problem persists, please repeat all the previous steps and make sure to follow everything to the letter
• Call a Corberó technical service and request a home visit for a more thorough inspection

We hope this article has been very helpful to you and that you have been able to fix error code 99 on your Corberó induction hob. Unfortunately, problems related to the PCB electronic board are very difficult to fix, however, we encourage you to try to solve this problem one way or another. Good luck and until next time!