Hoover Washing machine Error e03

What does it mean when the

Oh no! Is your Hoover washing machine showing the error code e03 and you don't know what to do? Well, don't worry, because today we're going to explain what this error code might mean, what its possible causes are, and how you can fix it quickly and easily.

This issue with Hoover washing machines indicates that there is a problem with water drainage. Keep in mind that the e03 error code is synonymous with error code 03, so the causes and solutions that can affect both problems are the same. Also, note that this error code affects Hoover Otsein series washers as well as many other models from the brand.

An error that can be frustrating for you and can have various causes. But first, let's briefly go over all the possible causes:

• A clogged drainage filter: The drainage filter of your washing machine may be clogged with objects such as coins, clips, lint, or other things that prevent water flow.
• A clogged, bent, or crushed drainage hose: The drainage hose may be blocked by an object or have an internal obstruction. It may also be bent or crushed, preventing the free flow of water.
• The drainage pump may be dirty or damaged: The drainage pump may be very dirty due to a malfunctioning filter, or it could also be damaged, preventing water from being evacuated from the washer.
• A failure in the water level sensor: A failure in this sensor can cause the washer to not detect the appropriate water level and therefore not drain the water correctly and safely.
• Issues with the internal wiring of your washer: A fault in the internal wiring that connects the drainage pump or the water level sensor to the PCB electronic board can generate these types of errors.

If your washer displays this error on the screen, don't be afraid and don't worry. Below, we'll give you a list of possible solutions that you can apply yourself without needing to call a technician.

Can we find a solution to the E03 error failure in the Hoover washing machine?

So that you can continue using your washing machine normally you have to follow these steps that we leave you below. Don't skip any and check everything carefully, take note of each one of them if necessary and follow everything to the letter:

1. Turn off and unplug your washer from the power source to reset it and refresh its sensors: This issue may be due to an electronic problem rather than a mechanical one, so a reset could be the solution to the entire problem. To do this, turn off your washer and proceed to unplug it from the power source. Wait a few minutes (at least 15) and then reconnect and turn it back on. Now start a washing cycle to check if the error code has disappeared. Sometimes electronic devices tend to fail because their internal memory can collapse, especially in newer models that are connected to the internet, so by doing this procedure, we clear all that internal memory that could be collapsed.
2. Clean the washer filter and make sure it is not clogged with dirt or foreign objects: Remember, this filter is designed only for water to pass through and not solid objects like coins, lint, clips, etc. The filter is a component that prevents impurities from entering the drainage pump and potentially clogging or damaging it. If the filter is dirty or clogged, water will not be able to circulate properly, causing this problem. To clean the filter, you'll need to open the bottom panel of the washer and locate it. Typically, it is next to the pump and has a twist-off cap for removal. Clean the filter with water, soap, and a little vinegar, you can also use a soft-bristled brush to help, and when it's clean, you can put it back in place. If you notice that the filter is broken or severely damaged, then you'll need to replace it with a new one compatible with your Hoover washer model.
3. Check the drainage pump and remove any objects that may be blocking it: The drainage pump of your Hoover washer is responsible for expelling water from the drum after the entire washing process. If something is hindering its operation, such as a coin, button, or piece of fabric, water will not be able to exit, and an error will occur on the screen. To access the pump, you'll need to open the bottom panel of the washer and locate it. It typically has a twist-off cap for removal. Clean the pump and reinstall it. Check that it functions correctly; otherwise, you'll need to replace it with a new one compatible with your Hoover washer model.
4. Inspect the drainage hose and ensure it is not bent, crushed, or damaged: The drainage hose in your washer connects the pump to the tube where water exits to the outside. If the hose is damaged or improperly positioned, water will not be able to exit, leading to washer malfunctions. To inspect the hose, you'll need to disconnect and remove it from your washer to check its condition. If you see that it is broken or punctured, you'll need to replace it with a new one. If it's bent or crushed, you'll need to straighten or adjust it so that it fits properly and isn't obstructed by anything, such as the wall or the washer itself. The hose may be clogged, so you can use a thin wire to insert it into the hose and carefully remove any dirt inside. You can also blow air through one end and check if dirt or any foreign objects come out the other end.
5. Check the water level sensor and verify that it functions correctly: The water level sensor detects how much water is in the drum and sends the signal to the PCB electronic board to activate or stop the drainage pump. If the sensor is damaged or improperly calibrated, it may send erroneous information, such as a false positive, causing the washer to be unable to drain water correctly. To check the sensor, you'll need to locate it on the top of the drum and measure it with a multimeter. If the values are abnormal or null, you'll need to replace it with a new one.
6. Inspect the internal wiring of your Hoover washer and ensure it is in very good condition: Sometimes rodents chew on the cables of your appliances to sharpen their teeth. Check all the wiring your washer uses to operate and make sure it is not cut, bitten, disconnected, or burnt. If you notice that there are cables in very poor condition, you'll need to replace them or make necessary repairs. Also, check the connections of all this wiring and make sure there is no sulfate or corrosion of any kind. If you've detected corrosion in the connections, then you'll need to perform maintenance to remove it completely.
7. If you've done everything mentioned above and the problem persists, you need to go over everything again: This time with more care and attention to detail, follow all the steps we've described to the letter. It's possible that you may have missed a detail or simply not performed a check correctly. Try everything again and verify if the error has disappeared from your washer. If the problem persists even after that, then the best thing you can do is leave the problem in the hands of washer experts.
8. Request a home visit from Hoover's technical support to find a solution to the problem: If after trying all the previous solutions the problem persists, it's likely a more complex issue that requires the intervention of a qualified professional. Don't attempt to manipulate the washer yourself, as you could cause more damage or void its warranty. Contact Hoover's technical service and request a visit for a qualified technician to inspect your washer and provide a definitive solution.

In summary, we have that the error code e03 and/or 03 in Hoover washing machines indicates a problem with water drainage. The most common causes may be a clogged filter, a clogged, kinked, crushed or damaged hose, a clogged or damaged drain pump, a faulty water level sensor, or an internal wiring problem. To solve it, you just have to follow the steps that we have recommended in our guide.

That's all for today! Thank you for reading us this far. We hope we have been very helpful to you in solving the problem your Hoover washing machine had. Good luck!