Beko Dishwasher Error e02

What is the fault of the E02 Beko error affecting your dishwasher?

If you've come across the E02 error code on your Beko brand dishwasher, then you're in the right place to find a solution. In this article, we will explain everything you need to know about this problem and how you can resolve it quickly and easily.

The E02 error code in Beko dishwashers indicates that there's an issue with the drainage or water outlet system in the dishwasher. This can be due to several reasons we'll list below:

• The filter is dirty or blocked by food residues or dirt
• The drain pump is damaged or jammed by a foreign object
• The drain/outlet hose is kinked, obstructed, or poorly connected
• The water level sensor is faulty or dirty due to lack of maintenance
• The water inlet valve is closed or damaged

Any of these causes can prevent the water from draining properly, causing the dishwasher to stop and display the E02 error code. Note that this type of error may have different variations in which they are all the same. What we mean is that the E02 error code is the same as the E2, 2, and 02 error codes.

How to fix the E02 error of the Beko dishwasher?

To resolve the E02 error code in Beko brand dishwashers, follow these steps outlined below:

1. Restart the dishwasher: Believe it or not, a simple restart can solve the problem. To do this, you will need to completely turn off the dishwasher and disconnect it from the power supply for a few minutes. Reconnect and turn it back on to check if the error has disappeared.
2. Clean the dishwasher filter: The filter is a part located at the bottom of the dishwasher, which retains food scraps and dirt generated during washing. If the filter is dirty or blocked, it can prevent the water from draining correctly. To clean it, carefully remove it and wash it with warm water and a bit of vinegar. If you don't have vinegar, you can use soap. Make sure to remove any leftover food or dirt trapped in the filter. Put the filter back in its place and check if the problem has been resolved. If the filter is broken, you'll need to replace it with a new one.
3. Check the drain pump: The pump is responsible for expelling water from the dishwasher to the drain hose. If the pump is damaged or jammed by food debris or any foreign object, it can prevent the water from draining properly. Typically, pumps accumulate solid food debris when the filter is broken or not working correctly. To check the pump, you'll need to access the inside of the dishwasher and locate it, which is usually near the filter. Check for any foreign objects that might be blocking the pump, such as plastic pieces, bones, coins, or dirt like grease or lint. If you find anything, remove it carefully and check if the problem has been resolved.
4. Check the drain hose: If this hose is bent, obstructed, or poorly connected, it can prevent the water from draining properly. Inspect it closely and ensure it's not being crushed against a wall, by the dishwasher itself, or by another appliance like the stove. Also, check for any bends or folds that could be restricting the flow of water. If so, carefully straighten the hose and see if this resolves the problem.
5. Check the water level sensor: This sensor is responsible for detecting the amount of water in the dishwasher and sending the signal to the electronic board to start or stop the wash cycle. If the sensor is defective or dirty, it can send a faulty signal, causing the dishwasher to stop and display the E02 error code. To check it, access the inside of the dishwasher and locate the sensor, usually near the filter or on the appliance's side wall. Check for any food residue or dirt that might be fouling the sensor. If so, clean it with an electronic cleaner and see if the issue has been resolved.
6. Inspect the water inlet valve: This valve regulates the flow of water entering the dishwasher from the supply network. If the valve is closed or damaged, it can prevent water from entering the dishwasher, causing it to stop and display the E02 error code. Locate this valve, typically connected to the water inlet hose. Check if the valve is open and if there are any signs of damage or leaks. If so, replace the valve with a new one and see if the issue has been resolved.
7. Repeat all the previous steps if the problem persists: We invite you to review everything we've previously described. Carry out a second check of everything and ensure you follow all our steps to the letter.
8. Reach out to Beko's technical support for assistance: If after going through all the steps and rechecking everything you still haven't solved the problem, the issue might be beyond our guidance, and expert intervention might be needed. Call Beko's technical service, explain your issue, and they will surely provide a quick and safe solution.

In summary, the E02 error code on your Beko dishwasher is related to a problem draining water. To resolve this issue, you'll need to check several things and take the following actions:

• Restart the dishwasher
• Clean the dishwasher filter
• Check the drain pump
• Inspect the drain hose
• Examine the water level sensor
• Review the water inlet valve
• Repeat all previous steps if the problem persists
• Contact Beko's technical support for assistance