Baxiroca Boiler Error e01

What is the fault of the E01 Baxiroca error affecting your boiler?

A Baxiroca boiler that might have gas problems? You've guessed it right. Although it's true that Baxiroca offers high-quality products, we still need to pay attention to its operation and occasionally perform its respective maintenance to prolong its lifespan.

It's important for you to know that this fault can also affect specific boiler models, namely Baxiroca Victoria 24/24F and Novanox 24/24F. While it's true that this error applies to all models, those two particular ones we mentioned earlier can also be affected.

The E01 error code in Baxiroca boilers indicates that we have an issue with the gas supply. Therefore, you'll need to perform various checks to get to the root of the problem.

Gas is crucial for the proper functioning of your boiler, as it fuels the entire heating system. It's important to address this fault as soon as possible, because if the issue turns out to be a gas leak, then the matter can become serious and complicated.

The E01 error code in Baxiroca boilers can be due to several reasons, such as:

• The gas valve or tap is closed or blocked
• The gas pressure is insufficient or irregular
• The gas pipe is obstructed or damaged
• The gas regulator is faulty or poorly adjusted
• The boiler burner is dirty or deteriorated

How to fix the E01 error of the Baxiroca boiler?

To resolve the E01 error code on Baxiroca boilers, follow these tips and advice outlined below:

1. Restart the boiler: As we know, the E10 error code is related to the gas supply, but it doesn't hurt to restart the boiler to release accumulated gases inside and reset all sensors. To do this, turn off the boiler, disconnect it from the power supply and wait a few minutes. Plug it back in, turn it on, and check if the error has disappeared.
2. Open the gas valve or tap: Are you sure that the gas valve is open enough to supply the boiler? Check that it isn’t closed, and if it's only slightly open, open it fully and check again if the error has disappeared from your boiler.
3. Check the gas pressure: Measure the gas pressure arriving at your boiler with a pressure gauge and compare it to the manufacturer's instructions. If the pressure is too low or fluctuates significantly, you may need to change the gas regulator or contact your gas supplier for an inspection.
4. Inspect the gas piping: Ensure that the pipe supplying gas to the boiler doesn’t have any cuts, bends, cracks, or even a dangerous leak. If you see any signs of damage, it should be replaced.
5. Check the gas regulator: Verify that the regulator controlling the gas flow to the boiler is in good condition and properly adjusted. If the regulator is broken or poorly calibrated, it should be replaced.
6. Clean the boiler burner: Using a soft brush, perform preventive maintenance on this burner. Clean the burner surface to remove any dirt or residue that may prevent its ignition or optimal operation. Dry it thoroughly before reconnecting it to the boiler.
7. Repeat all the above steps if the problem persists: Ensure that you follow all steps to the letter. Go over everything we've described above and make sure you've done everything correctly. If the problem continues, then it’s time to rely on the expertise of a professional.
8. Contact Baxiroca technical service to solve the problem: If you've been unable to resolve the E01 error code on your own, it's best to reach out to a qualified professional to inspect and repair your boiler if necessary.

In conclusion, these types of boilers are essential at home, especially in cold seasons or areas. But you must be cautious to ensure there's no kind of leak in the boiler to ensure its proper function and, most importantly, to prevent dangerous situations like a fire. To resolve the E01 error code on your Baxiroca boiler, you should do the following:

• Restart the boiler
• Open the gas valve or tap
• Check the gas pressure
• Inspect the gas piping
• Check the gas regulator
• Clean the boiler burner
• Repeat the above steps if the problem persists
• Seek help from Baxiroca's technical service if you can't solve the problem on your own